How do you cut and join waterproof LED strip lights?
Always use a sharp pair of scissors to cut your Waterproof LED Strip Light, dull scissors can damage the PC Board. Each waterproof strip light will have a cut mark between the two pairs of copper connection pads. Once you have located this cut line you can then cut your LED Strip Light to the desired length.
Even though LED Strip Lights use a low voltage direct current, exposure to water is still enought to short circuit the delicate components.
Waterproof LED strip lights can't be bent. This is because they're coated in waterproof silicone that isn't flexible enough to bend around corners, so you'll have to cut and solder the adjoining lengths.
If you are only using it indoors, there are water drops and splashes, and so a waterproofing level of IP65 basically is good enough. If you would like to install it in a place where it will be submerged in water for a long time, then we suggest that you utilize an LED strip light with a level of waterproofing of IP68.
Can an LED light strip be used in the shower? Yes, you may use LED lights in the shower. However, ensure that the lights do not become submerged in water as they are not waterproof.
Can you put a light over the shower? The simple answer is yes. You must choose a bathroom ceiling light that is rated for damp or wet areas. While these may seem like standard fixtures, they have extra features like a rubber gasket and glass lens or diffuser, that make the light moisture-resistant.
Two LED strips can be connected together by using strip connectors. There are two types of connectors; clip-on and fold over. The connector that you choose to use will depend on the type of strip lights that you are connecting.
The best way to get more brightness from an LED strip installation is to install multiple rows of the LED strip. With twice the number of LED strip rows, you will be able to directly double the amount of brightness.
During installation, make sure flexible light isn't receiving electricity in any manner. C) Make sure the voltage marked on your light strip matches the LED Driver. D) Do not overlap this product as the overlapping may cause the flexible light to overheat and melt or ignite.
The HR-ALU LED Extrusion is used with flexible or hard LED strips that are 8-10mm wide (0.39”). Due to its high integrity and compact size, it is ideal for use in bathroom, shower, floor applications or areas exposed to water.
Why do LED strips burn out?
Unlike incandescent bulbs which burn out and fluorescent lamps which begin to flicker, LEDs behave differently in that over time, they slowly and gradually lose their light output.
Yes! Flexible Neon LED strip lights can be used outdoors as long as they're marked as water resistant. You can tell if strip lighting is waterproof by checking its IP rating.
LED strips are designed to be very flexible. Their PCBs (printed circuit boards) are so robust that many LED tape products can be bent up to 90 degrees with no difficulty.
See clearly with a vanity mirror
Placing the LED light strip around the mirror will look more attractive, and most light strips have strong adhesive at the back so that you can directly attach them to the mirror. The daylight glow will make sure you always look your best.
Tape Size. A thick tape is better to use with LED strips.
LED strip lights are designed to make cutting easy, so all you will need is a pair of scissors. Either follow the cutting line (that sometimes also has a scissor icon on it) or cut between the pair of copper dots that show up at the end of each LED unit.
Is that possible? A: If the LED light strip you purchased can be cut, the remaining part that you have cut off cannot be used anymore. If you want to reconnect them after cutting, you must use an additional 4 pin connector to reconnect.
Providing that you cut along the marked cut lines only, LED strips — including certain Hue lightstrips — will work after cutting. Many people experience issues with their light strips if they cut outside of these lines. The cut lines are also the safest place to cut LED strips, as the circuits here are closed.
Vetco recommends, as a general rule, not to connect more than three complete strips end-to-end without adding in extra, higher gauge power wire or additional power supply units down the line.
To join two strip light sections together, use a connector clip. Push the open end of each strip into the clip, then close it to lock it in. To make your light strips go around a corner, use one corner connector and 2 connector clips. You can even make your strip lights go over uneven surfaces if you need to.
Can I put two LED strips together?
If they are compatible with each other i.e., both of them have same layout and also both are rated for same voltage, them you can connect two LED Strips from different brands. Voltage is another important thing to consider before connecting LED lights together.