When did furnaces stop using pilot lights? [Solved] (2022)

Table of Contents

Why do modern furnaces no longer use standing pilots?

The main issue with a standing gas pilot is that it must remain lit at all times so that your furnace is always available when the thermostat calls for heat. A small burner is continuously lit, which means it's always using fuel and costing you money. Lighting the pilot each year can be a struggle for some.... read more ›

(Video) Service of the antique pilot furnace part 1
(grayfurnaceman)

Do modern gas furnaces have pilot lights?

Newer gas furnaces (since about 2010) do not have a traditional pilot light that burns all the time. Instead they use electronic ignition systems that light only as needed. Constant flame or “standing pilot” heating systems are still fairly common in older homes, and they can still be repaired in most cases.... continue reading ›

(Video) How to adjust furnace pilot light
(themrhelperguy)

Are pilot lights obsolete?

Many homeowners may be surprised when they find out that their furnace doesn't have a pilot light (also known as a standing pilot or safety pilot). But pilot lights have become outdated technology for gas-powered furnaces and most other gas-burning appliances, like water heaters, fireplaces and stoves.... see details ›

(Video) FAQ How to Light a Pilot Light on the Furnace
(Bella Investment Group, LLC)

How do I know if my furnace has a pilot light?

If your furnace has a round knob on the gas valve with the words OFF/ON/PILOT, you have what's known as a standing pilot ignition.... continue reading ›

(Video) TOP 10 Reasons Why the Gas Pilot Light Goes Out & Won't Stay Lit!
(AC Service Tech LLC)

Does a furnace with electronic ignition have a pilot light?

If you have newer furnace, or you're planning on having one installed in the near future, it probably doesn't use a pilot light at all. Instead, an electronic ignition system ignites the burners. In fact, you rarely see standing pilot lights on newly manufactured furnaces anymore.... continue reading ›

(Video) Standing Pilot gas furnace operation and desmantaling
(Ty Branaman)

Can I replace a pilot light with electronic ignition?

When the pilot light of a gas-fired boiler or furnace burns constantly, energy is wasted. This type of pilot light can be replaced with an automatic electric ignition that ignites the pilot only when the thermostat calls for the furnace to be fired.... see details ›

(Video) How To Light your Furnace Pilot Light. Lighting Gas Heater Pilot Light -Jonny DIY
(Jonny DIY)

Can you manually light a gas furnace with electronic ignition?

If your furnace is equipped with an electronic igniter, you cannot light the furnace manually. However, you may be able to get the furnace working by turning off the igniter and resetting it. Find the paperwork for your particular furnace to locate the reset button or switch.... view details ›

(Video) How To Light Your Pilot Light (to your Furnace)
(John Birmingham)

Do Trane furnaces have a pilot light?

Furnace manufacturers have all but phased out standing pilot ignition systems for gas furnaces, so if you have to light the pilot light on your Trane furnace, it's because the furnace is more than 20 years old.... see details ›

(Video) Older Bryant furnace troubleshooting help needed. Gas valve? Circuit board? Pilot assembly?
(A Little Caulk and Paint)

Do pilot lights give off carbon monoxide?

It could be dangerous. But if your pilot light is yellow, or even if has a slight yellow or orange tint, then wasted energy may be the least of your concerns. A yellow or orange pilot light will produce carbon monoxide – an odourless, colourless gas that can fill your home and cause carbon monoxide poisoning.... view details ›

(Video) Gas Furnace Wont Ignite - How to Manually Light Burners
(Word of Advice TV)

Does turning off pilot light save gas?

As the weather gets warmer, you will be using your gas fireplace less and less. We recommend that you turn off your gas fireplace pilot light seasonally. Turning off your gas fireplace's pilot light can save a substantial amount of energy and money.... view details ›

(Video) Furnace Starts Then Stops - Troubleshooting | Repair and Replace
(AMRE Supply)

Does turning off the pilot light save money?

You can get savings and conserve energy if you turn off your pilot light. A white sulfur-based film can develop on the inner glass if the pilot light is kept on for a while without turning on the main burner. This byproduct can build up over time. Always follow the manufacturer's recommendation for cleaning the film.... see details ›

(Video) How to furnace pilot light adjust and find adj screw
(themrhelperguy)

Do all propane furnaces have a pilot light?

Most older propane gas furnaces (and some new ones) are ignited with a pilot light (many newer models use an electronic ignition for better efficiency). One of the main reasons your furnace stops working is because that pilot light goes out.... see more ›

When did furnaces stop using pilot lights? [Solved] (2022)

Do all gas furnaces have a flame sensor?

Not all furnaces have a flame sensor, but if your furnace has one, it will be mounted close to the burner with the metal rod positioned in the flame. Flame sensors vary in size (2 to 4 inches) and shape (see examples below).... view details ›

Should the pilot light always be on in a gas stove?

In older gas stoves, a small light called a pilot should constantly be on. This tiny flame is used to light bigger ones on your stovetop burners and oven.... view details ›

How do you relight an automatic pilot light?

Relight a Natural Gas Furnace - YouTube... see details ›

How do you start a furnace manually?

Once the gas has had time to dissipate, turn the knob to "Pilot." Then, hold down the "Reset" button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light. Once you are sure the pilot light is on, release your pressure on the reset button.... see more ›

Will my gas furnace work without electricity?

For the vast majority of homeowners who use a furnace with natural gas for heat, an electrical outage means the furnace won't work. The furnace's safety system will not allow it to turn on during an electrical outage. It is not safe to try to rig the furnace for heating, as this can compromise health and safety.... continue reading ›

How does electronic ignition furnace work?

This system uses a pilot flame, but the flame lights only when there's a call for heat from the thermostat. The furnace's electronic control board activates an electric igniter that uses a high-voltage spark to light the pilot. In turn, the pilot lights the gas for the burners.... continue reading ›

How does an electric pilot light work?

In a pilot light, one of the junctions of a thermocouple is sitting in the pilot light's flame. The electricity that is created runs to a small electromagnetic valve and holds it open. If the pilot light blows out, the thermocouple quickly cools off. It stops generating electricity and the valve closes.... see more ›

How does a standing pilot gas valve work?

A bit of composite metal wire, called a “thermocouple,” connects the burner to a valve in the gas line. When the pilot light is lit, the thermocouple registers the heat and generates an electric current. The current travels down the thermocouple to the gas valve and opens it. This is what keeps the pilot light burning.... continue reading ›

Can hear your furnace click on but it does not fire up?

You Have a Faulty Ignition Sensor (Pilot Light)

The pilot light or ignition sensor is usually the most common issue when your furnace will not ignite. This is typically the problem if you can hear your furnace click on but it does not fire up.... read more ›

How much does a new furnace cost?

A new furnace replacement can cost between $3,000 - $7,600, depending on the size of your home, the efficiency of your new furnace, and the sophistication of the equipment. That includes labor and permit fees, not just equipment costs.... read more ›

What does a thermocouple look like on a furnace?

Furnace - Thermocouple | Repair and Replace - YouTube... view details ›

How much does it cost to relight a pilot light?

The Cost of Relighting the Pilot Light

A plumber can help reignite the pilot light. They will charge you an hourly fee of $40 to $150. This is usually a fairly brief project, and may just take an hour.... see more ›

Are pilot light heaters safe?

If you have a furnace that was made in the last 10 to 15 years, then chances are it still relies on a pilot light as an ignition source. Appliances equipped with a pilot light always pose a significant hazard that could result in serious injury or worse.... continue reading ›

Does a Trane furnace have a reset button?

Turn off the power and open up the control panel to access the reset buttons on these models. Next, lift the cover to the blower compartment, and you should see the reset button sitting next to the blower motor and blower wheel.... view details ›

Do AC units have pilot lights?

Your central air heating unit, depending on the make and model, depends on a pilot light to work correctly. The pilot light is used as a source of heat to ignite the unit.... read more ›

Where is pilot light Goodman furnace?

The pilot light on a Goodman furnace is located inside the front panel and in front of the heat exchanger. To access it, you'll need to remove the front panel of the furnace. If your pilot light goes out, you can light it manually in case of an emergency.... see more ›

Should a pilot light be orange?

The flames from traditional pilot lights should burn a bright blue color. If your pilot light's flame is orange or yellow, it is burning inefficiently due to a lack of oxygen. The thermocouple should sense when this happens because the heat from the flame will not be as hot as it should be.... continue reading ›

How do you fix a yellow flame on a gas furnace?

Dirt in the burner is the most common cause of a yellow flame, and it prevents the gas and air from mixing properly. A call to a technician for cleaning and evaluation is needed to fix that problem.... continue reading ›

Why does my pilot light burn yellow?

A yellow flame is caused by lack of oxygen and incomplete combustion. If the pilot light is a weak yellow flame it will not get hot enough to heat the thermocouple to the temperature needed to enable the gas valve to open. This is often caused by a dirty pilot tube tip.... view details ›

How much does a pilot light cost per month?

Monthly costs of running a pilot light range from $4.49/month (natural gas) to $11.34/month (propane). Pilot lights that run on propane are about 2 times more expensive to run than pilot lights running on natural gas (that's because natural gas is cheaper per produced BTU – British Thermal Unit).... continue reading ›

Does a pilot light use much gas?

Just how much gas does a pilot light consume? Most pilot lights will consume about 600 BTU's of gas/hour. With 24 hours in a day, that's roughly 14,400/BTU's each day. Figuring 30 days, a pilot light will use approximately 432,000 BTU each month.... see details ›

Is it bad to turn the furnace on and off?

Turning your heat or your air conditioning off may not damage your system, but you may experience “collateral damage.” For example, if your house gets cold during the day and the temperatures are low outside, your pipes may freeze and burst.... see more ›

Should I turn off the pilot light on my gas furnace in the summer?

Most modern mid to high efficiency gas furnaces no longer have a pilot light. It's been replaced by an electronic ignition. As a result, the furnace will not need to continuously burn gas in order to keep a pilot light going, making it unnecessary to turn off your furnace for the summer.... read more ›

Is it OK to turn off gas to furnace?

To uphold safety, you can turn off the gas supply to the furnace. But be careful not to turn off the gas supply to the rest of the house. You'll still need it for cooking, cleaning, heating water, and other activities in summer. It is also advisable to schedule an inspection of your home's safety systems.... see details ›

Should I turn off gas to furnace during summer?

It's a good idea to turn off your furnace during hot months. If left on, it will continue to consume energy. The furnace contains some electrical components like sensors that can needlessly draw power throughout the summer. If your furnace has a pilot light, it will use up unnecessary gas during summer when left on.... continue reading ›

Does my Rheem furnace have a pilot light?

You can find the pilot light near the bottom of your furnace. If it is turned on, turn the gas control setting to "off." See to it that the pilot light goes out.... view details ›

Why does pilot light go out on propane furnace?

A system leak – A weak or yellow pilot light flame usually indicates a leak somewhere in your system; as a safety measure, your furnace responds to that leak by shutting down. Drafts – Most pilot lights simply blow out due to a draft in your basement or storage room.... read more ›

Why does the pilot light keep going out on my propane heater?

If the thermocouple is too far from the flame, this can cause the pilot to go out and shut down the propane heater; you can fix this easily by moving the thermocouple closer to the flame. The thermocouple could also be worn out, in which case it needs to be replaced.... view details ›

Can a furnace work without a flame sensor?

Without a flame sensor, your furnace will keep emitting gas even when there's nothing to ignite it, resulting in hazardous gas buildup. If your flame sensor is dirty or faulty, it will automatically shut down the heating unit if it doesn't detect a flame.... view details ›

Where is the flame sensor on an old Rheem furnace?

To do its job, the sensor probe must extend into the burner compartment, while the base with the wire connection must be outside, so the sensor is mounted on the wall of the burner housing. On a Rheem furnace, it's directly in front of you when you remove the access cover.... see more ›

Can you bypass the flame sensor on a furnace?

Yes. You can bypass the flame sensor. However, if you do so, you can't manually light your furnace, and you've got to have proper bypassing safety measures in place. But it's advisable not to bypass the flame sensor.... view details ›

Is it safe to leave pilot light on?

Generally speaking, it is safe to leave your continuous pilot light on at all times, assuming it stays lit (more on this in a moment). While it does cost more to keep your pilot light on in between uses, it can actually have some benefits to your system.... read more ›

Are old stoves safe?

Old appliances can electrocute you and start a fire. They may be a “bargain,” but not when you consider the safety risks. If you absolutely want to keep your vintage appliance, our advice is to have a professional appliance repair company perform a safety inspection.... see details ›

Why did the pilot light go out?

Some of the possible serious reasons for pilot lights to go out include loose or broken gas valves, thermocouples or heat exchangers, faulty venting, low gas pressure, or high winds. If you believe there is a serious problem, don't hesitate to contact a professional.... see details ›

What is the efficiency of a standing pilot furnace?

55 to 72 percent AFUE Furnaces (Low Efficiency)

Non-electronic, standing pilot ignition.... see details ›

Why are standard low efficiency furnaces no longer manufactured?

Why are standard low-efficiency furnaces no longer manufactured? They cannot provide the minimum 80 percent AFUE required by DOT. A Category I furnace operates with a: High-temperature, negative-pressure vent.... read more ›

How do you test a furnace safety if it uses a standing pilot?

Inspecting the Pilot Light Flame

To inspect the operation of the standing pilot light. Remove the furnace cover panel, which should expose the burner assembly and pilot. You should be able to see the flame of the pilot light. If the pilot light is out, attempt to relight it.... see details ›

What is a standing pilot furnace?

A standing pilot is the standard ignition device for most natural gas burning heating systems, and has been for many years. It's a continuously burning flame at the bottom of the heater, responsible for starting the burners that actually generate heat for the home.... view details ›

Do high-efficiency furnaces last longer?

High-efficiency furnaces may also last longer than traditional gas furnaces. This means you won't have to worry about replacing your furnace yet again in just a few years. This is another reason they are considered a smart investment.... view details ›

Are gas furnaces more efficient now?

And New Furnaces Are Indeed Much More Efficient

New furnaces, however, can have AFUEs from 80% all the way to 98.5%. In order for a gas furnace to earn the ENERGY STAR certification, it must have an AFUE of 90% or greater.... read more ›

Why do most furnaces today use burners?

Why do most furnaces today use in-shot burners? They are more efficient and they fit today's narrow heat exchangers better.... see details ›

Will natural gas be phased out?

While there are efforts to eventually phase out the use of natural gas, most experts are of the opinion this would likely not happen until 2040, at the earliest.... continue reading ›

How efficient is a 30 year old furnace?

Standard gas furnaces have an AFUE rating of at least 80 percent. High-efficiency furnaces carry ratings of 90 percent or more. With a top-of-the-line unit, you can enjoy an AFUE rating of up to 97 percent.... view details ›

Are 80 Percent furnaces being phased out?

This is a big change coming in residential & light-commercial furnaces. Effective June 1, 2013, federal law requires that minimum furnace efficiency in the Northwest must be 90%. That means that 80 percent of furnaces cannot be installed after that date.... see more ›

Should the flame touch the thermocouple?

The flame should strong enough to cover about 1/2 inch at the end of the thermocouple tip. If the flame is too strong and not adjusted correctly, it will be blue and may make a hissing sound as the flame crosses the thermocouple.... see details ›

How close should the thermocouple be to the pilot light?

When working properly in most gas appliances, the pilot flame should hit the upper 1/2 to 3/8 of the thermocouple.... view details ›

What color should your furnace flame be?

The burner flames from your natural gas furnace should look blue or almost completely blue. A healthy natural gas furnace flame is characterized by a roaring blue flame with a light blue triangle in its center. There may be a tiny tip of yellow.... continue reading ›

Why does my pilot light not stay on?

If your pilot light won't stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.... view details ›

How much gas does a pilot light use?

Just how much gas does a pilot light consume? Most pilot lights will consume about 600 BTU's of gas/hour. With 24 hours in a day, that's roughly 14,400/BTU's each day. Figuring 30 days, a pilot light will use approximately 432,000 BTU each month.... read more ›

What type of burner is found in most modern furnaces today?

The burner in your gas furnace is ignited either by an electronic ignition, found in most modern furnaces, or with a standing pilot flame, which is common in older-style furnaces that have an annual fuel utilization efficiency (AFUE) rating of less than 80 percent.... continue reading ›

Popular posts

You might also like

Latest Posts

Article information

Author: Fr. Dewey Fisher

Last Updated: 12/01/2022

Views: 5900

Rating: 4.1 / 5 (42 voted)

Reviews: 89% of readers found this page helpful

Author information

Name: Fr. Dewey Fisher

Birthday: 1993-03-26

Address: 917 Hyun Views, Rogahnmouth, KY 91013-8827

Phone: +5938540192553

Job: Administration Developer

Hobby: Embroidery, Horseback riding, Juggling, Urban exploration, Skiing, Cycling, Handball

Introduction: My name is Fr. Dewey Fisher, I am a powerful, open, faithful, combative, spotless, faithful, fair person who loves writing and wants to share my knowledge and understanding with you.